Mounting A Tub
Mounting A Tub
Blog Article
Were you hunting for advise concerning Installing A Bathtub?
Mounting a bathtub isn't precisely rocket science, however it does call for strong plumbing, carpentry, as well as often, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is readily available, the job can relocate quickly; if you have to open up a wall surface to get rid of the old tub as well as place the brand-new bath tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly need an assistant to vacate the old tub as well as embeded in the brand-new one. Make sure you have certified on your own for the work and fit trying it. Rather than employing a service provider to take over a halfway-completed job, it is far better to take into consideration using one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This short article will certainly aid you install a new bathtub in your restroom if you have actually already purchased a brand-new bathtub and don't need to transform the arrangement of your previous water system pipelines.
Your tools as well as product list should make up the following:
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, then the first thing you must do is separate the water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The procedure of eliminating the existing faucets can be quite troublesome as a result of the limited access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipes. Once the supply pipes have been eliminated, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before moving on to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location in between the tap as well as the sink. Protect the tap in place with the maker supplied backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be attached to the faucet finishes first, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Tub
Utilizing both wood boards under its feet, position the tub in the called for setting. The wood boards are practical in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub till the level reviews degree.
To mount faucets, fit all-time low of the furthest versatile tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water and also inspect all joints as well as new pipework for leakages and also tighten them if needed. Fill up the bathtub and additionally inspect the overflow electrical outlet as well as the normal outlet for leakages.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been utilized a minimum of when as this will certainly settle it into its last setting.
Preparing for the Installment
First of all, the supporting structure provided with the bathroom ought to be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps unit to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture a stiff seal, creating the water to penetrate the wall surface between the bathroom and the tiling, resulting in difficulties with moisture and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and installations. They are marketed in tubes and cartridges, and also are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill the tub with water prior to securing, to allow for the movement experienced when the tub is in usage. The sealer can fracture rather early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our article about A Step-by-Step Guide to Installing a Bathtub. Thanks a ton for taking the time to browse our piece of content. Sharing is caring. Helping people is fun. Thanks a lot for your time. Don't forget to pay a visit to our website back soon.
Get A Quote
Report this page